Cost guides
What furnace repair costs for furnace repair.
What furnace repair costs
Prices in this category are quoted per unit — per square foot, per linear foot, per pier, per job — and the unit is where most quotes become incomparable. The table below is the range we verified in November 2026, with what each line includes.
| Job | Typical range | Notes |
|---|---|---|
| Furnace repair | $150-$600 | Diagnostic plus common parts |
| Furnace replacement | $3,000-$8,000 | 80-96% AFUE, installed |
| Tune-up and safety check | $100-$250 | Annual |
| Heat pump installation | $5,000-$12,000 | Including ductwork changes |
| Duct cleaning | $300-$800 | Per system |
| Emergency call-out | $200-$500 | Nights and weekends |
What moves the price
- Access. Height, water, tight side yards and finished interiors all add labour.
- Prep. Cleaning, grinding, draining or removing an old system is often the largest hidden line.
- Materials. The same job in a premium finish can double the material cost.
- Permits and disposal. $100–$800 depending on the jurisdiction and the waste stream.
- Season. Spring and autumn are busy; February is not.
What a quote should show
Ask for the same five lines from every contractor: unit price and quantity, prep included, materials by brand, permits and disposal, and the warranty. A quote that only shows a total is a price, not a scope.
The methods hub explains what each option actually does, and the problems hub starts with the diagnosis every quote should follow.
Is the cheapest quote a red flag?
Usually it is a scope difference — less prep, no permit, thinner material. Compare the five lines, not the total.
How long is a quote valid?
30 days is common; material prices move. Ask what happens if you sign after the window.
All cost guides
Blower motor failure: what a fix costs
A capacitor is $150 to $300, a motor $400 to $900, an ECM module $300 to $600. Four worked jobs and the test that stops you buying a motor you don't need.
Read the guide →
Boiler cost: what a new boiler costs in the US
A replacement boiler runs $4,000 to $8,000, or $6,000 to $12,000 for high-efficiency condensing. Here is the line-by-line arithmetic and what moves it.
Read the guide →
Ductless mini-split cost: what a system runs installed
A single-zone ductless mini-split runs $3,000 to $5,500 installed, and three zones $7,500 to $12,000. Here is the line-by-line arithmetic behind both.
Read the guide →
Electric furnace cost: what installation runs in 2026
An electric furnace costs $3,000 to $6,500 installed. The panel and circuit are the swing factors, and resistance heat costs more to run than gas.
Read the guide →
Furnace repair cost per square foot
Furnace repair runs about $0.08 to $0.40 per square foot of house. Here is the arithmetic, why the metric misleads, and when it is useful.
Read the guide →
Gas furnace cost: what a replacement runs in 2026
A gas furnace costs $3,000 to $8,000 installed. Here is the line-by-line arithmetic, the efficiency premium, and when repair beats replacement.
Read the guide →
Heat pump cost: what US homeowners pay in 2026
A heat pump install runs $5,000 to $12,000 in the US. Here is the line-by-line arithmetic, what moves the price, and when repair beats replacement.
Read the guide →
How much does furnace repair cost?
Furnace repair in the US runs $150 to $600, with a typical bill near $350. See what each repair type costs and how the total is built.
Read the guide →
Is furnace repair worth it?
Repair is worth it when the cost per remaining year is low. Here is the payback math, the 50 percent rule, and the cases where replacement wins.
Read the guide →
No heat: what a fix costs, fault by fault
Most no-heat repairs run $150 to $600 including the diagnostic. Here is what each fault costs, worked through with arithmetic, plus the after-hours premium.
Read the guide →
Pilot light out: what a fix costs
A thermocouple runs $150 to $300, a pilot assembly $200 to $400, a gas valve up to $600. Four worked estimates with every line item shown.
Read the guide →
Short cycling: what a fix costs, cause by cause
Most short-cycling fixes run $150 to $600 including the diagnostic. Here is the arithmetic for each cause, plus the running cost of leaving it alone.
Read the guide →
Strange smell: what a fix costs
From a $15 filter to $800 of duct cleaning, what each furnace smell costs to fix, with four worked jobs and the safety exceptions that cost nothing.
Read the guide →
Thermostat not responding: what a fix costs
A thermostat is $150 to $400 installed, wiring $150 to $400, a board $300 to $600. What each fault costs, with four worked jobs and what to check free.
Read the guide →